注册 登录  
 加关注
查看详情
   显示下一条  |  关闭
温馨提示!由于新浪微博认证机制调整,您的新浪微博帐号绑定已过期,请重新绑定!立即重新绑定新浪微博》  |  关闭

天色轨迹-冷冰川的柴火间

所谓柴火间,就是杂七杂八。这里漫聊着属于普通人的科学和跆拳道哲学^.^

 
 
 

日志

 
 
关于我

●本人热爱自然科学,具体说来~天文,植物,地质,化石,矿物。。。从小就都喜欢。喜欢收集它们。 ●本人喜欢摄影,这是随着我的天文附带起来的,尤其喜欢记录天空中的颜色。 ●本人喜欢跆拳道,它不仅仅是运动,里面还充满了实践的哲学。 ●本人喜欢做饭,自己做便宜又吃得饱。 ●本人喜欢骑自行车,从初中就喜欢骑着车去野外。 ●本人喜欢做实验,只听书上讲的太没意思了。

[资料]LRGB imaging  

2008-06-05 20:36:45|  分类: 作为资料留着 |  标签: |举报 |字号 订阅

  下载LOFTER 我的照片书  |
It is common in astronomy imaging, especially deep sky, to use a technique called LRGB image compostion in order to get the best colour images. This involves capturing separate red, green, and blue images to compose the colour, and also a high-quality monochrome image to act as the luminance (brightness) of the final image.
On this page I have written up my notes which hopefully will give some guidance to others trying this technique.

Credit must go to fellow QCUIAG member Jan Timmermans. At the time of writing this page Jan was also developing his LRGB technique and I am grateful for his valuable input. Jan's LRGB web page is at http://www.madpc.net/~firmament/lrgb.html.

Mention must also be made of Peter Lloyd, Jim Thommes, and Rob Kantelberg for their input and websites.

1. Capture

When capturing images, you must use coloured filters to capture individual frames of red, green, and blue, and a luminance filter for the L channel. I now use Astronomik Type II filters, which are parfocal and complement each other in relation to the colours that they pass. All are IR-blocking, in fact the L filter is simply an IR blocker.
It is usual to capture more frames of luminance than of each colour. This is because you want the best possible quality for the luminance. Of course you want good quality colour too, but you can get away with fewer frames. Make sure you know which capture files are which colour! As the example images below show, they will all be greyscale, and therefore you can't tell afterwards.
There are ways to decide how many exposures of each colour to capture, involving capturing an image of a type G2V star with your camera, and analysing it to calibrate your exposure times for each colour (different cameras will vary). But for the time being I capture approximately equal amounts of each and adjust colour levels later.
Here are some original frames from my image of NGC 4631, the Whale Galaxy:
Luminance Red
Green Blue

2. Image Calibration

Images should be calibrated as well as you can using dark, flat, and bias images. The purpose of this is to remove artifacts like glow from the camera electronics, hot pixels, and some camera noise, and to ensure as far as possible a uniform image with dark and light patches (caused for example by vignetting or dust spots) eliminated. My preferred method for doing this with webcam images is to use Carsten Arnholm's ImageTOOLSca software as follows:
  • Export AVI frames to monochrome FITs, selecting the Y luminance channel and applying gamma correction as necessary (see Robin Leadbeater's work on webcams HERE. Put red, green, blue, luminance, flat, dark, bias frames in different file directories
  • Browse through image files and "trash" those of low quality
  • Enter Calibration dialog and create master Bias. Flat, Dark frames
  • Apply calibration to image files (luminance, red, green and blue).

3. Align and Stack Separately

The separate groups of FITs files must be loaded into Registax 4 and each one aligned, stacked and saved in 32-bit FITs format. Note at this stage in Registax, colour must be disabled, otherwise you will not get a proper monochrome image saved. File names must end with _R, _G, and _B to indicate red, green, and blue image files (this is not just for your convenience, it makes the compose step work properly). Stack the luminance too.
Luminance stacked Green stacked

4. Post-process Luminance

Load the luminance file into PixInsight LE or some other image processing application, and apply usual processing steps (stretch, sharpening, noise reduction etc.)
Processed Luminance Image

5. Compose the separate R/G/B images into one colour image

For this I use the popular software Registax. This software is more well-known for use in aligning and stacking images, but it can be used effectively for this job too. Load the _R, _G, and _B image files into Registax 4. Make sure the "Colour" checkbox is checked on the Select page and again on the Stack page. When Registax suggests you process in black and white, because the files are black and white, choose NO. This is very important!
Align and stack all three images. The result will be a composite RGB colour image. Don't worry if the colours don't look good, they can be adjusted afterwards. You might find it helpful to go to the Wavelet page and use the RGB Align feature to fine-tune the alignment of the colours. Save in TIFF format.
RGB Combined

6. Adjust Colours

Load the colour image into your image processing application and stretch etc. until the colours look reasonable. If you have any pattern noise, such as diagonal banding (very common with modified webcams) remove it at this stage as it can distort the colour image. Save the image.
Initial Processed RGB Image

7. Add Luminance Layer

Load the luminance image, and the rgb composite image into The Gimp or Photoshop. First you must make those two images the same size and orientation. You can find the adjustments necessary using AstroWave or using the Gimp measuring tool. Rotate the colour image if necessary and resize if it needs it.
NOTE: Always make changes of this type to the colour image, not the luminance
After the colour image has been resized and/or rotated, follow these steps to create the composite:
  • Make a copy of the luminance image and set the image mode to RGB (it will be monochrome)
  • Blur the colour image slightly by applying a gaussian blur of around 5 pixels. Increase the saturation of this image.
  • Copy the colour image using Edit->Copy, then move to the luminance image and use Edit->Paste to insert it as a new layer. In The Gimp you must then click the new layer button to make the pasted selection a permanent layer.
  • Align the colour layer with the luminance underneath - I like to do this by setting the layer mode to "Difference" and using the move tool to move it around until the image is as black as possible. Then set the layer mode to "Colour".
  • Depending on the image, you may want to reduce the opacity to something less than 100%. Some people like to reduce it to 50%, process the image further and then apply luminance over the top (In The Gimp use layer mode "Value").
  • Save image.

8. Final Post-processing

Finally, I use The Gimp and/or PixInsight LE to tweak the colours, reduce noise, and perform any other post processing I find to be necessary.
LRGB Combined and Processed - click for full size

转载地址:http://www.davesastro.co.uk/techniques/lrgb.html

  评论这张
 
阅读(229)| 评论(0)
推荐 转载

历史上的今天

在LOFTER的更多文章

评论

<#--最新日志,群博日志--> <#--推荐日志--> <#--引用记录--> <#--博主推荐--> <#--随机阅读--> <#--首页推荐--> <#--历史上的今天--> <#--被推荐日志--> <#--上一篇,下一篇--> <#-- 热度 --> <#-- 网易新闻广告 --> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构--> <#--博主发起的投票-->
 
 
 
 
 
 
 
 
 
 
 
 
 
 

页脚

网易公司版权所有 ©1997-2018